Dental Lab Flexible Denture Material Injection System Injector Machine 110v

  

Specification Voltage: AC 110V/60Hz Power: 400 watts Heating temperature: 282-288 ° C Pressurization time: 7 minutes 30 seconds - 11 minutes Packing size: 403457cm Gross weight: 30kg Using Steps: 1 The function of the heater is to heat the ink cartridge at a temperature of 282-288 ° C for about 7 minutes 30 seconds - 11 minutes to melt the flexible denture material in the ink cartridge. 2 The function of the hot press is to inject molten material into a previously prepared flask.

3 The heater will beep when it is heated. Note Please read the product manual carefully before operating the machine. 1x Heater 1x Hot Press 1x Picking Stick 1x Small Top bar 1x Big Top bar 1x Type Box 1x Box Wrench 1x Power Cord 1x Product Brochure. Denture Injection System + Dental Flask Flexible Machine 400W 110V Lab Equipment. De-ntal Flexible Denture Machine Lab Equipment.

Dentistry Injection System 400W 110V 282-288 ° C. Dental Flexible Denture Machine Is a 400w/110v Dental Laboratory Equipment for Making Flexible Removable Partial Dentures. The Denture Produced by the Invisible Denture Injection Molding Machine Has Almost No Waste Edge, and the Grinding Process Can Be Completed at One Time.

The Denture Injection System Is Easy to Operate, Has a Long Service Life, Low Maintenance Cost, High Success Rate, and Dental Laboratory Equipment for Denture Injection System, Which Is Very Necessary for Dentists. This Machine Is Produced According to International Standards. The Operation Is Simple, Time-saving, the Casting Success Rate Is High, and the Common Tooth Box Can Also Be Injection Molded. The Denture Injection Unit Consists of a Heater and a Hot Press. Heaters: Temperature Control, Timers and Electrical Systems.

Hot Presses: Frames, Cylinders, Heaters, Brackets and Flasks. 7 Minutes 30 Seconds - 11 Minutes. 1 the Function of the Heater Is to Heat the Ink Cartridge at a Temperature of 282-288 ° C for About 7 Minutes 30 Seconds - 11 Minutes to Melt the Flexible Denture Material in the Ink Cartridge. 2 the Function of the Hot Press Is to Inject Molten Material into a Previously Prepared Flask.

3 the Heater Will Beep When It Is Heated. Please Read the Product Manual Carefully Before Operating the Machine. The sale of this item may be subject to regulation by the U. Food and Drug Administration and. State and local regulatory agencies. If the item is subject to FDA regulation. If you have questions about legal obligations regarding sales of medical devices.

You should consult with the FDA's Center for Devices and Radiological Health. Thank you for your cooperation. We try our best to reply to your emails as soon as possible, however, due to high volume of daily incoming emails and time zone difference, we may not be able to reply your emails immediately. Please give us the opportunity to resolve any problem. We understand the concerns and frustrations you might have, and will try our best to resolve the issues.

Feedback is very important to us. It is impossible to address issues if we do not know about them! Faction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount.

Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday. 7 minutes 30 seconds - 11 minutes. Dental Lab Flexible Denture Machine. This item is in the category "Business & Industrial\Healthcare, Lab & Dental\Other Healthcare, Lab & Dental".

The seller is "weofferbestgoods" and is located in this country: US. This item can be shipped to United States.

1. Voltage: AC 110V/60Hz
2. Power: 400 watts
3. Heating temperature: 282-288 ° C
4. Pressurization time: 7 minutes 30 seconds - 11 minutes
5. Packing size: 40*34*57cm
6. Gross weight: 30kg
7. Brand: Unbranded
8. Type: Dental Lab Flexible Denture Machine
9. Intended Use/Discipline: Dentistry